Page Comparison

JP14

Set no jumper to enable M.2 on CN11
Set jumper 1-2 to disable M.2 on CN11

Unplugged

JP15

Unplugged

JP13

Set no jumper to disable eDP-to-LVDS CONV
Set jumper 1-2 to enable eDP-to-LVDS CONV

Unplugged

JP1

Set no jumpers to enable M.2 on CN12
Set jumper 1-2 to disable M.2 on CN12

Unplugged

JP2

Unplugged

JP3

COM1

Set no jumper for RS-485
Set jumper 1-2 for RS-422
Set jumper 2-3 for RS-232

Unplugged

JP4

COM2

Set no jumper for RS-485
Set jumper 1-2 for RS-422
Set jumper 2-3 for RS-232

Unplugged

JP16

PANEL BACKLIGHT VOLTAGE

Set jumper 1-2 for 12V
Set jumper 2-3 for 5V

2-3 Plugged

JP17

PANEL VDD VOLTAGE

Set jumper 1-2 for 5V
Set jumper 2-3 for 3.3V

2-3 Plugged

JP10

PANEL INTERFACE

Set no jumper for LVDS
Set jumper 1-2 for eDP

Unplugged

JP12

BIOS_DIS1

Set JP8 JP11 and no JP7for JP12 for SPI on carrier
Otherwise for SPI on module

Unplugged

JP11

BIOS_DIS0

Unplugged

JP9

VDD_EN Level

Set no jumper for 3.3V
Set jumper 1-2 for 5V

Unplugged

JP8

BKLT_EN Level

Set no jumper for 3.3V
Set jumper 1-2 for 5V

Unplugged

JP6

BKLT_CTRL Level

Set no jumper for 3.3V
Set jumper 1-2 for 5V

Unplugged

JP5

GPIO/SD

Set no jumper for GPIO
set jumper 1-2 for SD CARD

Plugged

CN11

Set jumper 1-2 for TYPE mode Set jumper 2-3 for no TYPE/AT mode

1-2 Plugged

J2

Set jumper 1-2 for ATX mode
Set jumper 2-3 for AT mode 1-2 Plugged

CN6

Set jumper 1-2 for battery disconnected
Set jumper 2-3 for battery connected
Set no jumper for RTC current measurement

2-3 Plugged

JP2

Set no jumper for
+5V_SB_MOD current
measurement

Plugged

JP12

PANEL BACKLIGHT VOLTAGE SELECTION

Set jumper1-2 for 12V
Set jumper 2-3 for5V

2-3 Plugged

JP13

PANEL VDD VOLTAGE SELECTION

Set jumper 1-2 for 5V
Set jumper 2-3 for 3.3V 2 -3 Plugged

JP11

PANEL INTERFACE SELECTION

Set jumper for eDP
Set no jumper for LVDS

Unplugged

JP8

BIOS_DIS1

for

Unplugged

JP7

BIOS_DIS0

Unplugged

JP10

GPIO/ SD Set no jumper for GPIO
Set jumper for SD CARD

Plugged

JP5

COM1

Set no jumper for RS-485
Set 1-2 for RS-422
Set 2-3 for RS-232

Unplugged

JP6

COM2

Set no jumper for RS-485
Set 1-2 for RS-422
Set 2-3 for RS-232

Unplugged

JP4

ESPI/LPC# SELECTION

Set jumper for switch enabled
Set no jumper for switch disabled

Plugged

JP3

ESPI/LPC# SELECTION

Set jumper for LPC from CEXP Set Set no jumper for ESPI from CEXP

Plugged

JP14

MIC#_SEL

Set no jumper for MIC2
Set jumper for MIC1

Plugged

JP9

3-WIRES/4-WIRES FAN TACH DRIVER

Set jumper 1-2 for 4-wires fan
Set jumper 2-3 for 3-wires fan

1-2 Plugged

JP1

Set jumper for BATLOW# enabled
Set no jumper for BATLOW# disabled

Unplugged

CN3

Set jumper 1-2 for PSU PWR_OK
Set jumper 2-3 for PWR_OK always high

1-2 Plugged