Versions Compared

Old Version 1

changes.mady.by.user Giuseppe Pagano (Deactivated)

Saved on

compared with

New Version Current

changes.mady.by.user Giuseppe Pagano (Deactivated)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

On SECO Android 11 BSP it is possible to create and test custom devicetree“devicetree.dtb dtb” and overlay“overlay.dtbo file dtbo” files for implementing and validating custom DISPLAY configuration and or peripherals.

You can customize and test new dtb/dtbo file files without the use of using external resourceresources, you just need the seco SECO board, and a PC (windows Windows or Linux) for connecting to it with ADB protocol (via USB cable or over IP).

Please refer to Connecting via ADB for detailed instructions on HOW TO connect the board via ADB.

Procedure

  • Connect to the board via ADB protocol (ref to Connecting via ADB for details) or via Serial cable

  • Enter in the folder /data/seco/dts_sourcesources:

    • cd /data/seco/dts_sourcesources

  • Inside “seco/” folder you will find the dts sources files you can modify and compile for changing default dtb or dtbo

    • Here is an example from c43 board:

...

  • You can edit .dts files using the vi editor included in our Android distribution and adding or changing sections add or change dts code in the source files.

    • Example command for editing devicetree dts file on C43 board:

      Code Block
      vi seco/seco-imx8qm-c43.dts

    • Example command for editing overlays dts file on C43 board:

      Code Block
      vi seco/overlays/seco-imx8qm-c43-lvds-GENERIC-single-channel-overlay.dts

  • After having changed the sources file with the right setup, it is possible to compile dtb and dtbo binary files with the script ./dtscompile.sh <file_to_be_compied>compiled>:

    Code Block
    ./dtscompile.sh  seco/overlays/seco-imx8qm-c43-lvds-GENERIC-single-channel-overlay.dts

  • or:

    Code Block
    ./dtscompile.sh  seco/seco-imx8qm-c43.dts

  • Results will be copied in /data/seco/ folder:

    • /data/seco/overlay.dtbo

    • /data/seco/devicetree.dtb

  • You can edit /data/seco/android_seco.conf:

    Code Block
    vi /data/seco/android_seco.conf

  • and add in it the following definitions:

    Code Block
    ### Enable dtb customization
#
enablecustomization=true

### Definitions for dtb custom file
customdtb=devicetree.dtb

### Definitions for device tree overlay custom file
customdtbo=overlay.dtbo

  • N.B. If you are defining a new video output you need also to unconfigure any defined video:

    Code Block
    ### Force video selection. 
# Posible values are: NONE, LVD0, ... LVD6, HDM0, HIN0, EDP0, HLV0, ELV0, LEH0, EHD0
videosel=NONE

  • The changes will be applied starting from the next reboot.

  • At startup pay attention to the following messages for verifiying verifying the new setup:

    Code Block
    switch to partitions #0, OK
mmc0(part 0) is current device
587 bytes read in 11 ms (51.8 KiB/s)
 verify OK, boot 'boot_a'
Found custom dtb of size 165905 in path /misc/seco/devicetree.dtb  <----
165905 bytes read in 13 ms (12.2 MiB/s)       <---------- size
Found custom dtbo of size 3147 in path /misc/seco/overlay.dtbo    <-----
3147 bytes read in 12 ms (255.9 KiB/s)        <---------- size
Warn! Can't find videoselection NONE in dtbo image.    <-------
Kernel load addr 0x80280000 size 43283 KiB
kernel   @ 80280000 (44321280)
ramdisk  @ 86400000 (8505136)
fdt       @ 83e80000 (165905)       <----------  size
## Flattened Device Tree blob at 83e80000
   Booting using the fdt blob at 0x83e80000
   Using Device Tree in place at 0000000083e80000, end 0000000083f2bfff

  • NP.BS. If you prefer you can edit dts files on you Descktop your Desktop PC, and copy them using adb push command:

    Code Block
    adb push seco-imx8qm-c43.dts /data/seco/seco/seco-imx8qm-c43.dts
adb push test.dtb /data/seco/overlays/seco-imx8qm-c43-lvds-GENERIC-single-channel-overlay.dts

  • NP.NP.BS. It is also possible to customize only the dtb or only the dtbo file. If only one of this these files has been found, the default configuration will be used instead of the missing one.