Page Comparison

It is possible to install Android 11 on the following boards:

SBC-

3.5-MX8M-Mini (C61)

SECO Android 11 BSP supports every possible C61 configuration, regardless ram all SBC-3.5-MX8M-Mini (C61) configurations (RAM size, eMMC size and , peripherals).

You can also use all installation methods described below to install Android 11 on C61 board with 1 Giga of ram, but clearly the performance will be reduced, and it will be possible to run only 1 single application after startupthe C61.

Running Android 11 on SBC-3.5-MX8M-Mini (C61) board with 1 Giga RAM is deprecated. You can install Android 11 on C61 board following one of the procedures described belowIf you use it, you will find that performance is reduced and only a single application can be run after startup.

SBC-

3.5-MX8 (C43)

SECO Android 11 BSP supports every possible C43 configuration, regardless ram all SBC-3.5-MX8 (C43) configurations (regardless RAM size, eMMC size, and peripherals).

You can install Android 11 on C43 board only with The SBC-3.5-MX8 (C43) board only supports the usb OTG cable installation procedure, and does not support the uSD/USB procedures.

Android 11 support for C43 SECO SBC boards includes:

• Wifi/BT

• USB otg/ADB

• audio codecSound support

• HDMI and LVDS display

• + touchscreen support

• Double ethernet card

• OTA update

Installation Methods

You may use any of the following three methods to install Android 11 on Seco boardSECO boards:

1. via an OTG cable;

2. using a uSD card;

3. using

1. a USB flash drive.

Your board may not support all three methods (see above).

Anchor
otg otg

HOW TO install SECO Android 11 BSP on onboard eMMC via OTG cable

To flash Android 11 on SECO board using a OTG cable, please follow these simple steps:

1. Download the correct SECO Android 11 image for your board according to the SECO BSP table

1. .

2. Insert jumper for board RECOVERY boot (refer to RECOVERY BOOT JUMPER table to locate it)

3. Connect the OTG cable between Board and PC (refer to OTG connector TABLE for locating it).

4. Power on the board

5. Follow

1. the procedure according to the system that you are using:

Anchor
usd usd

HOW TO install and boot SECO Android 11 BSP on external uSD card

To prepare a bootable Android 11 uSD for SECO board, please follow these simple steps:

1. Download the correct SECO Android 11 image for your board according to SECO BSP table.

1. Extract the downloaded image:

   Code Block
   tar xzf <ANDROID_IMAGE_FILENAME>.tar.gz

1. Enter in the Android IMAGE folder:

   Code Block
   cd <ANDROID_IMAGE_FOLDER>

2. Insert a clean uSD card in the card reader of your Linux computer

3. Identify the path to your uSD card:

   Code Block
   lsblk

1. Execute the script android_

1. write_

1. device.sh to flash the card

   Code Block
   ./android_write_device.sh /dev/<PATH_TO_SD_CARD>

To boot from uSD card

1. Identify the jumper for ALTERNATE BOOT on the board

1. and insert it. Refer to ALTERNATE BOOT JUMPER table to locate it

1. .

2. Insert the uSD card in the card slot

1. on the board.

2. Power on the board

Anchor
usb usb

HOW TO install SECO Android 11 BSP from USB key

This procedure can be done in 3 steps:

STEP 1)

• Download the SECO Unified Installation Key (SUIK) image from this link: SUIK IMAGE

• Unzip the downloaded file.

• Write the binary USB recovery key image on the USB pen. If you do not know how to write a raw image on a USB stick, please refer to this procedure:

Write a raw image on USB key using Rufus

• (Use dd tool from Linux OS, or Rufus, Win32 Disk image or equivalent tools, to write the usb key image from a Windows systems)

STEP 2

• Download the Android11 image for the selected board. Please refer to table “SECO ANDROID 11 BSP table“ to choose the right one.

• Extract the downloaded image on the first partition of the USB key (FAT32 filesystem with the label “IMAGES”) and rename the target folder to ANDROID.

• Disconnect the USB key from the PC

STEP 3)

• Insert the SUIK USB key on one USB port of the SECO Board

• Power on the board.You can

• follow the installation process via At startup open the serial console and execute the following commands:

  Code Block
  mount /dev/sda1 /mnt cd /mnt/ANDROID/ ./android_write_device.sh /dev/mmcblk0

• Wait until fashing script procedure has finished

Anchor
and_bsp_tb and_bsp_tb

SECO ANDROID 11 BSP table

Anchor
rec_boot_jps_tb rec_boot_jps_tb

RECOVERY BOOT JUMPER (BOOT from usb OTG)

BOARD	Jumper name	Position	Picture
SBC-C61	CN52	1-2

Image Removed

Image Added

SBC-C43

CN44

JP2

1-2

Image Removed

2-3	Image Added

Anchor
otg_conn_tb otg_conn_tb

OTG connectors

BOARD	Connecton name	Picture
SBC-C61	CN36-OTG

Image Removed

Image Added
SBC-C43	CN44

Image Removed

Image Added

Anchor
alt_boot_jps_tb alt_boot_jps_tb

ALTERNATE BOOT JUMPER (boot from uSD)

BOARD	Jumper name	Position	Picture
SBC-C61	CN52	2-3

Image Removed

Image Added