| Info |
|---|
Depending on the configuration and following revisions, the features of the board are subject to change. For detailed information on hardware specifications, please visit www.seco.com |
INDEX
How can I configure jumpers?
Component | Description | Use | Default configuration (Fig.1) |
|---|---|---|---|
JP14 |
| Set no jumper to enable M.2 on CN11 | Unplugged |
JP15 |
| Unplugged | |
JP13 | Set no jumper to disable eDP-to-LVDS CONV | Unplugged | |
JP1 | Set no jumpers to enable M.2 on CN12 | Unplugged | |
JP2 | Unplugged | ||
JP3 | COM1 | Set no jumper for RS-485 | Unplugged |
JP4 | COM2 | Set no jumper for RS-485 | Unplugged |
JP16 | PANEL BACKLIGHT VOLTAGE | Set jumper 1-2 for 12V | 2-3 Plugged |
JP17 | PANEL VDD VOLTAGE | Set jumper 1-2 for 5V | 2-3 Plugged |
JP10 | PANEL INTERFACE | Set no jumper for LVDS | Unplugged |
JP12 | BIOS_DIS1 | Set |
JP11 and no |
JP12 for SPI on carrier | Unplugged | ||
JP11 | BIOS_DIS0 | Unplugged | |
JP9 | VDD_EN Level | Set no jumper for 3.3V | Unplugged |
JP8 | BKLT_EN Level | Set no jumper for 3.3V | Unplugged |
JP6 | BKLT_CTRL Level | Set no jumper for 3.3V | Unplugged |
JP5 | GPIO/SD | Set no jumper for GPIO |
Plugged
Depending on the configuration and following revisions, the features of the board are subject to change. For detailed information on hardware specifications, please visit www.seco.com
INDEX
| Table of Contents | ||
|---|---|---|
|
How can I configure jumpers?
Component
Description
Use
Default configuration (Fig.1)
CN11
Set jumper 1-2 for TYPE mode Set jumper 2-3 for no TYPE/AT mode
1-2 Plugged
J2
Set jumper 1-2 for ATX mode
Set jumper 2-3 for AT mode
1-2 Plugged
CN6
Set jumper 1-2 for battery disconnected
Set jumper 2-3 for battery connected
Set no jumper for RTC current measurement
2-3 Plugged
JP2
Set no jumper for
+5V_SB_MOD current
measurement
Plugged
JP12
PANEL BACKLIGHT VOLTAGE SELECTION
Set jumper 2-3 for5V
Plugged |
JP13
PANEL VDD VOLTAGE SELECTION
Set jumper 1-2 for 5V
Set jumper 2-3 for 3.3V
2-3 Plugged
JP11
PANEL INTERFACE SELECTION
Set jumper for eDP
Set no jumper for LVDS
Unplugged
JP8
BIOS_DIS1
Set JP8 and no JP7for SPI on carrier
Otherwise for SPI on module
Unplugged
JP7
BIOS_DIS0
Unplugged
JP10
GPIO/SD
Set no jumper for GPIO
Set jumper for SD CARD
Plugged
JP5
COM1
Set no jumper for RS-485
Set 1-2 for RS-422
Set 2-3 for RS-232
Unplugged
JP6
COM2
Set no jumper for RS-485
Set 1-2 for RS-422
Set 2-3 for RS-232
Unplugged
JP4
ESPI/LPC# SELECTION
Set jumper for switch enabled
Set no jumper for switch disabled
Plugged
JP3
ESPI/LPC# SELECTION
Set jumper for LPC from CEXP Set Set no jumper for ESPI from CEXP
Plugged
JP14
MIC#_SEL
Set no jumper for MIC2
Set jumper for MIC1
Plugged
JP9
3-WIRES/4-WIRES FAN TACH DRIVER
Set jumper 1-2 for 4-wires fan
Set jumper 2-3 for 3-wires fan
1-2 Plugged
JP1
Set jumper for BATLOW# enabled
Set no jumper for BATLOW# disabled
Unplugged
CN3
Set jumper 1-2 for PSU PWR_OK
Set jumper 2-3 for PWR_OK always high
1-2 Plugged
Fig. 1: Description of jumpers possible configuration for jumpers
What to connect and where?
Further information about placement and description of connectors are available here.