| Gallery | ||||||
|---|---|---|---|---|---|---|
|
| Info |
|---|
Depending on the configuration and following revisions, the board’s features are subject to change. For detailed information on hardware specifications, please visit www.seco.com. |
DORIS is a low-end Single Board Computer with NXP i.MX6 Processor, that exploits the potential of a configurable expansion connector to fully meet any configuration flexibility needs. This SBC is ideal for digital signage, infotainment applications, and in all general purpose contexts requiring multimedia capabilities and high performance for the reproduction of relevant and/or engaging contents.
For ordering purposes, the DORIS is referred to by its base code, “A62”.
INDEX
| Table of Contents |
|---|
How can I power on my module?
https://secogroup.atlassian.net/l/c/gzj1qAat
What will I find in my module?
Off-the-shelf products are shipped with a standard in-house-developed software.
The definition of standard, in this case, is “the environment which SECO adopts for validation”.
Anyway, custom in-house-developedsoftware with different defaults can be built.
Contact your reference sales for further information.
What can I do now?
| Blog Posts | ||||
|---|---|---|---|---|
|
What are the features of the module?
The SBC-A62-J allows to directly access to some of the features of i.MX6 processor through the pin multiplexing. On-board there is a dedicated 32-pin expansion connector (J8, see Fig. 1) which is a standard dual-way male pin header.
Below is a description of the pinout configuration.
Pin Number | Pin Name | Pinout Configuration Options | Port Number | ||
|---|---|---|---|---|---|
VCC_SW | x | x | x | x | |
2. | 3P3V | x | x | x | x |
3. | GND | x | x | x | x |
4. | EXP_GPIO_1 | x | GPIO1_IO09 | x | 1 |
5. | EXP_GPIO_2 | ECSPI2_MISO | GPIO2_IO25 | x | 2 |
6. | EXP_GPIO_3 | ECSPI2_SCLK | GPIO2_IO23 | x | 2 |
7. | EXP_GPIO_4 | ECSPI2_MOSI | GPIO2_IO24 | x | 2 |
8. | EXP_GPIO_5 | ECSPI2_SS0 | GPIO3_IO29 | x | 2 |
9. | EXP_GPIO_6 | FLEXCAN1_TX | GPIO1_IO07 | x | 3 |
10. | EXP_GPIO_7 | FLEXCAN1_RX | GPIO1_IO08 | x | 3 |
11. | EXP_GPIO_8 | UART4_CTS_B | GPIO6_IO03 | x | 4 |
12. | EXP_GPIO_9 | UART4_TX_DATA | GPIO5_IO30 | x | 4 |
13. | EXP_GPIO_10 | UART4_RTS_B | GPIO6_IO02 | x | 4 |
14. | EXP_GPIO_11 | UART4_RX_DATA | GPIO5_IO31 | x | 4 |
15. | EXP_GPIO_12 | x | GPIO3_IO28 | I2C1_SDA | 5 |
16. | EXP_GPIO_13 | SPDIF_IN | GPIO3_IO21 | I2C1_SCL | 5 |
17. | EXP_GPIO_14 | SPDIF_OUT1 | GPIO4_IO05 | x | 5 |
18. | EXP_GPIO_15 | SD1_CMD | GPIO1_IO18 | PWM4_OUT | 6 |
19. | EXP_GPIO_16 | SD1_CLK | GPIO1_IO20 | x | 6 |
20. | EXP_GPIO_17 | SD1_DATA0 | GPIO1_IO16 | x | 6 |
21. | EXP_GPIO_18 | SD1_DATA1 | GPIO1_IO17 | PWM3_OUT | 6 |
22. | EXP_GPIO_19 | SD1_DATA2 | GPIO1_IO19 | PWM2_OUT | 6 |
23. | EXP_GPIO_20 | SD1_DATA3 | GPIO1_IO21 | x | 6 |
24. | EXP_GPIO_21 | I2C3_SDA | GPIO7_IO11 | x | 7 |
25. | EXP_GPIO_22 | I2C3_SCL | GPIO1_IO03 | x | 7 |
26. | EXP_GPIO_23 | UART1_RX_DATA | GPIO5_IO29 | x | 8 |
27. | EXP_GPIO_24 | UART1_TX_DATA | GPIO5_IO28 | x | 8 |
28. | EXP_GPIO_25 | UART5_RX_DATA | GPIO6_IO01 | x | 9 |
29. | EXP_GPIO_26 | UART5_TX_DATA | GPIO6_IO00 | x | 9 |
30. | EXP_GPIO_27 | UART5_RTS_B | GPIO4_IO14 | FLEXCAN2_TX | 10 |
31. | EXP_GPIO_28 | UART5_CTS_B | GPIO4_IO15 | FLEXCAN2_RX | 10 |
32. | GND | x | x | x | x |
Accessories
These are the accessories offered by SECO for DORIS SBC.
For more information, click on the accessory of your interest.
Accessory | Description |
|---|---|
Camera module with integrated KLT Auto-Focus 5MP and FCC cable (15 cm, 16-poles). Available in two versions:
| |
Display kit with 7” TFT RGB Display and I2C capacitive Touch Screen, and video cable | |
Display kit with 15,6" LVDS display and video cable | |
IEEE 802.11 b/g/n WiFi Module based on Ralink RT5370 chipset, with 7-pin USB interface | |
IEEE 802.11 b/g/n WiFi Module based on Ralink RT3070 Chipset, with external 50Ω 2.4GHZ antenna and 6-pin USB interface |
| Note |
|---|
Please note that the KIT-WIFI-3M08-1 and the KIT-WIFI-3M08-2 have USB interfaces with a different number of pins. Each one can only be used with a board with the same number of pins. |
Downloads
Edgehog OS
Starting from Linux Kernel version 5.10, the Board Support Package (BSP) for this board is fully integrated within Edgehog OS, the operating system for the All-In-One IIot platform CLEA developed by SECO and based on Yocto. Edgehog OS is intended to provide the highest standards in terms of security and stability thanks to features like OTA (Over the Air) updates, double partitions, and fallback procedures. Edgehog OS integrates a Device Manager to communicate with the Cloud and allows a family of products to be managed as a fleet.
Source code:
The source code for Edgehog OS can be found at the following link.
Binaries:
The binaries (U-Boot, Linux Kernel, Yocto image) associated with the various Edgehog OS releases can be found at the following link.
Legacy Software
This section contains releases (source code and binaries) for older BSPs and Yocto images.
Source code:
Source code for linux kernel, u-boot and yocto seco layers is available here.
Binaries
:Here you can find the latest binaries available:
Board configuration | Version | image | filesystem | u-boot | kernel |
|---|---|---|---|---|---|
SBC - 512M 2x256M | 4.19.35 - 3.4.0 | ||||
SBC - 1G 4x256M | 4.19.35 - 3.4.0 | ||||
SBC - 2G 4x512M | 4.19.35 - 3.4.0 | ||||
SYS- 512M 2x256M | 4.19.35 - 3.4.0 | ||||
SYS - 1G 4x256M | 4.19.35 - 3.4.0 | ||||
SYS - 2G 4x512M | 4.19.35 - 3.4.0 |