Trizeps USB-Driver
- Albinleo Velappan (Deactivated)
- Sven Hillger
This describes the settings for the USB driver of the Trizeps-module.
Trizeps 4
The Trizeps IV(M) has three USB-Ports:
USB-Host
USB-OTG
USB-Slave
If a cable is attached to the USB-Slave port, the USB-OTG port is automatically disabled. After deattach of the cable it gets reconnected.
Trizeps 5
The Trizeps V has three USB-Ports:
USB-Host
USB-OTG
USB-Slave (HighSpeed)
Unlike Trizeps4, where USB-Slave can't work at the same time as USB-OTG, all ports may run concurrently.
| ||
|---|---|---|
Key | Type | Description |
HighSpeed | DWORD | 0 Only use Full-Speed for USB-Slave port. Note that this does not work,
if the module is attached to a USB-hub.
1 Use High-Speed. |
Trizeps 6
The Trizeps VI has two USB-Ports:
USB-Host (HighSpeed)
USB-OTG (HighSpeed)
A mounting option exist to route the USB-OTG-pins to the USB-Slave-pins of Trizeps4&5. But this might impact the usable speed on the USB-bus and is not the default setting.
For a normal configured Trizeps6, you should set the OTG-Registry setting to one of following values:
0: if USB-OTG should only work as Host ( Also set DynamicClientLoad = 0).
3: if you attached a OTG-connecter (with ID and VBUS pins).
5: if you attached a OTG or USB-Slave connector and the port should work as Slave only.
0x20005: if you want to operate the USB-Port as USB-Slave, but left VBUS floating. (This setting is usefull if you want to debug an application through ActiveSync, but can only connect to a USB-A connector).
| ||
|---|---|---|
| ||
| ||
Key | Type | Description |
HighSpeed | DWORD | 0 Force port to only use Full-Speed.
1 Use High-Speed. |
Registry-Settings for the USB-OTG Port (all Trizeps)
| ||
|---|---|---|
| ||
Key | Type | Description |
OTG | DWORD | 0x......FF OTGMode:
0x0 (default): OTG-Port is Host, or disabled if USB cable is plugged.
0x2: Switch mode depending on USB-Slave-Cable detect pin.
cable plugged: Slave, cable not plugged: Host.
0x3: Switch mode depending on OTG-ID-Pin (Status is polled).
0x5: OTG-Port is Slave only.
0x6: Switch manually (set cable=1 !) more info: (*) follow link @end of table
0x....FF.. GPIO to switch external charge-pump (5V enable for OTG-port).
Use 0x10 for GPIO_0.
Use 0x00 to disable this feature.
0x...1.... Inverse polarity of external charge-pump-enable pin (5V).
0x...2.... Keep VBUS-powered (Trizeps6 only: VBUS-Input need 5V if OTGMode = 0x5.
This bit only needs to be set if VBUS is not supplied by external pin!)
0x...4.... Ignore VBUS-Input. (Trizeps6 only; 15.04.2016)
0x...8.... Simplified OTG mechanism. (Trizeps6 only; 20.09.2016) |
cable | DWORD | Use USB Slave Cable-Detect-pin. (30.06.2009)
0 or missing use pin 55 of SODIMM200 as usb-cable-detect.
1 attempt to detect cable by host SOF-messages.
2 attempt to detect cable by VBUS Signal. (13.10.2009) |
(* more info) switchingusbfn.
See Also
switchingusbfn,
Connect USB-Host-Connector to a Trizeps,
Connect USB-Slave-Connector to a Trizeps