CQ7-A30

Depending on the configuration and following revisions, the features of the board are subject to change. For detailed information on hardware specifications, please visit www.seco.com

INDEX

1 How can I configure jumpers?
2 How can I configure micro switches?
3 What to connect and where?
4 Accessories

How can I configure jumpers?

Component	Description	Use	Default configuration (Fig.1)

Component	Description	Use	Default configuration (Fig.1)
JP10	CAN_VDD	Set jumper 1-2 for 12V CAN_VDD Set jumper 2-3 for 5V CAN_VDD	1-2 Plugged
JP11	CAN_TERM	No jumper for no termination Set jumper 1-2 for 120 Ohm termination	Plugged
JP21	JTAG TD0	Set jumper 1-2 for JTAG debug Set jumper 2-3 for USB debug	2-3 Plugged
JP20	JTAG TD1	Set jumper 1-2 for JTAG debug Set jumper 2-3 for USB debug	2-3 Plugged
JP12	ADR SEL	Set jumper 1-2 for 80/84h Set jumper 2-3 for 90/94h	2-3 Plugged
JP25		Set no jumper for CN41-3 open Set jumper 1-2 for JTAG_TRST# on CN41-3 (JTAG Connector)	Plugged
JP24		Set jumper 1-2 for RSTBTN# TO SRST# Set jumper 2-3 for JTAG_TRST# TO SRST#	1-2 Plugged
JP19	JTAG TRST	Set jumper 1-2 for JTAG_TRST# pulled-up Set jumper 2-3 for JTAG_TRST# pulled-down	1-2 Plugged
JP18	JTAG TMS	Set jumper 1-2 for JTAG_TMS pulled-up Set jumper 2-3 for JTAG_TMS pulled-down	1-2 Plugged
JP14	LID	Set no jumper for normal operation Set jumper 1-2 for LIDBTN simulation	Unplugged
JP4	BOOT ALT	Set jumper 1-2 for boot from off module BIOS FLASH Set no jumper for boot from on module BIOS FLASH	Unplugged
JP5	Wire HDMI CEC	Set jumper 1-2 for 1-Wire BUS Set jumper 2-3 for HDMI CEC	1-2 Plugged
JP15	FAN 0	Set jumper 1-2 for 12V FAN Set jumper 2-3 for 5V FAN	1-2 Plugged
JP16	FAN 1	Set jumper 1-2 for 12V FAN Set jumper 2-3 for 5V FAN	1-2 Plugged
JP17	FAN 1 CTRL	Set jumper 1-2 for FAN1 w/o control Set no jumper for FAN1 with control	Unplugged
JP22	V5A BYPASS	Set no jumper for AT no 5V_SBY mode Set jumper 1-2 for AT/ATX 5V_SBY mode	Plugged
JP13	RTC CMOS	Set jumper 1-2 for normal operation Set jumper 2-3 for Battery disconnecting	1-2 Plugged
JP1	PEG EN	Set no jumper for PCIe x1 Set jumper 1-2 for PEG	Unplugged
JP6	WLAN DISABLE	Set no jumper for RF operation allowed Set jumper 1-2 for no RF operation allowed	Unplugged
JP23	ATX MODE/AT MODE	Set 1-2 for ATX PSU controlled Set 2-3 for ATX PSU in AT mode	1-2 Plugged

_{Fig. 1:}_{Description of jumpers possible configuration}

How can I configure micro switches?

Description	Default Configuration (Fig. 2)

Description	Default Configuration (Fig. 2)
	Position 1-8	Position 2-7	Position 3-6	Position 4-5
SW1	OFF	OFF	OFF	OFF
SW2	OFF	OFF	ON	OFF
SW6	ON	OFF	ON	OFF
SW11	ON	ON	ON	ON
SW12	ON	ON	ON	ON

_{Fig. 2:}_{Description of possible switches configuration}

What to connect and where?

Further information about placement and description of connectors are available here.

Accessories

^{Fig. 3:}^VA64

^{Fig. 4:}^VA65

VA64

VA64
Component	Use	Default configuration (Fig.1)
JP1	Set jumper 1-2 for 12V backlight voltage Set jumper 2-3 for 5V backlight voltage	1-2 Plugged
JP2	Set jumper 1-2 for 5V digital voltage Set jumper 2-3 for 3.3V digital voltage	2-3 Plugged
JP6	Set no jumper for 30p eDP connector Set jumper 1-2 for 40p eDP connector	Unplugged
JP5	Set no jumper for 30p eDP connector Set jumper 1-2 for 40p eDP connector	Unplugged
JP3	Set jumper 1-2 for 12V backlight voltage Set jumper 2-3 for 5V backlight voltage	1-2 Plugged
JP4	Set jumper 1-2 for 5V digital voltage Set jumper 2-3 for 3.3V digital voltage	2-3 Plugged