i-PAN T7 II + Trizeps VIII Series

Owned by Oleksii Kutuzov
Last updated: 13. Jun 2024 by Michael Schieren
1 min read

Eval-Kit specification (without Trizeps Module)

  • 1pc of Frame with i-PAN T7 II FF (incl. Housing) and Display

  • 1pc of 12-24 V power supply

  • 1pc of i-MODCON RS232

  • 1pc of i-MOD Camera OV5640

  • 1pc of stand

  • 1pc of USB-A (male) to micro USB-cable

  • 1pc of Serial-cable

‌

Features

  1. Vin 12V-24V DC

  2. VIN_FUSED Supply and Power failure GPIO for USV

  3. 2x USB Host/ 1x USB-OTG

  4. 10/100 MBit Ethernet

  5. Audio (Stereo Headphone, Microphone , Line-In, Speaker out)

  6. LVDS-Display , HDMI, RGB

  7. UART, RS-232, CAN, SDIO, I2C

Software (OS Images)

Trizeps VIII Mini

OS

Bootloader

Kernel

Release

Download

OS

Bootloader

Kernel

Release

Download

Windows 10 IoT Enterprise

2020.04 / kuk_imx_v2020.04

BSP 1-5-0

2024-05-03

IoTEntOnSECO_1-5-0

2020.04 / kuk_imx_v2020.04

BSP 1-4-0

2023-04-11

winpe_enterprise_1-4-0_20230411

Android

Debian 12

2020.04 / kuk_imx_v2020.04

5.10.9 / kuk_lf-5.10.y_android-compilable

2024-03-27

seco_tr8mini-ipant7_bookworm_20240327

Yocto

2020.04 / kuk_imx_v2020.04

5.10 / kuk_lf-5.10.y_android-compilable

2023-05-30

hardknott_weston_chromium-20230530

Trizeps VIII Plus

OS

Bootloader

Kernel

Release

Download

OS

Bootloader

Kernel

Release

Download

Windows 10 IoT Enterp.

 

 

 

 

Android

Debian 12

2020.04 / kuk_imx_v2020.04

5.10.9 / kuk_lf-5.10.y_android-compilable

2024-03-27

seco_tr8plus-ipant7_bookworm_20240327

Yocto

2020.04 / kuk_imx_v2020.04

5.10 / kuk_lf-5.10.y_android-compilable

2023-05-12

trizeps8plus-ipant7-v2-hardknott_weston_chromium-20230512

Initial Setup

In general the Eval-Kit is pre-configured and tested with the OS you ordered.

Please check if all connections are correct.

If needed prepare everything for debug connection by using connector U12. ( for details next chapter)

Plug in the power adapter into the 12V Jack (J17) and 120VAC~240VAC to power source.

The system will start up and OS will be visible on the Display. The Boot messages are printed within the PC terminal window.

Establish a Serial Connection

  1. Connect the baseboard to a computer using a serial cable and a serial adapter.

  2. You will need a Tera Term application to communicate with the device.

  3. In Tera Term configure the serial connection in Setup-> Serial Port. Set the following settings:

    • Port: serial-port, to which device is connected

    • Speed: 115200

    • Data: 8bit

    • Parity: none

    • Stop bits: 1

  4. Plug the power connector in, the device will boot up, you should see the terminal output if settings are correct, and correct port is selected.

Links

U-Boot, Trizeps VIII Mini | How to Make U Boot for Trizeps VIII Mini

U-Boot, Trizeps VIII Plus | How to Make U Boot for Trizeps VIII Plus

Linux 5.10, Trizeps VIII (-/Mini/Plus) | How to Build Linux Kernel for Trizeps VIII & Trizeps VIII Mini

Deploy Debian and Yocto

How to deploy Windows 10 IoT Enterprise to Trizeps VIII Mini / Trizeps VIII Plus

‌